arduino stepper motor serial control cable

#Arduino stepper motor serial control cable serial#
#Arduino stepper motor serial control cable driver#
#Arduino stepper motor serial control cable full#
#Arduino stepper motor serial control cable windows 8#
#Arduino stepper motor serial control cable free#

Set the power jumper in 'stand alone' positionĬonnect GND from your ATX power supply to USB header Pin1 (where the black triangle is)Ĭonnect 5 VSB from your ATX power supply (+5 VDC Standby Voltage) to USB header Pin4Ĭonnect GND and PS ON (Power Supply On) from your ATX power supply to PS ON header, polarity doesn't matter The Rumba uses a standard USB Mini-b (5-pin) female connector. MINTEMP triggered !Įrror:Printer stopped due to errors.

#Arduino stepper motor serial control cable free#

with Arduino IDE 1.0.6) (the exact message might differ):Įcho: Last Updated: 13:06:11 | Author: Įcho: Free Memory: 3632 PlannerBufferBytes: 1232Įcho:Acceleration: S=acceleration, T=retract accelerationĮcho:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s)Įcho: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00

#Arduino stepper motor serial control cable serial#

If you orient the plug on Rumba pin1-to-cable-pin1 - and plug exp1-to-exp1 and exp2-to-exp2 you will get the following error meassage when surveying the serial port (via USB on Rumba e.g. And to further 'confuse you', the 'Smart Controller' plug exp1 must NOT go to exp1 - it should go to exp2 on Rumba.

The following confusion was encountered with Rumba (board blue LKDR20150602, also see #RepRapDiscount_Smart_Controller) and Smart Controller from kickstarter 'Prusa i3 with Diamond Hot end': Rumba-boards small white triangle (pin 1 indication - visible if no plug) is inconsistent with the cable red-line indicating pin-1. Run the cables exactly as shown on the images.

easy to develop/debug new or optimized firmware using Atmel Studio.

#Arduino stepper motor serial control cable full#

JTAG can be used during full operation (no shared pins).

Power and ALL unused pins available on EXP-3 feature connector:.

USB connector and USB pin header (useful when mounting in a small box).

can be used with existing 4 pin Molex plug on motor cable.

screw terminals *and* pin header for easy motor connection:.

can be used for mechanical, opto, hall.

6x end stop connectors with power supply.

1x PWM capable power mosfet with extended cooling area for heated bed.

3x (MainPower) extruder heater cartridge/power resistor + 1x (12V) fan + 1x (12V) light

5x PWM capable power mosfet outputs (3 with voltage selector for MainPower/12V):.

3x extruder thermistor + 1x heated bed thermistor + 1x chamber thermistor

5x temperature ADC connectors for thermistors:.

#Arduino stepper motor serial control cable driver#

up to 6 motor driver with easy micro stepping setup (micro switches) which can be used for:.

RepRapDiscount SmartController compatible pin header on board.

power input selector for ATmega/logic (stand alone or power from USB).

integrated high precision power regulators (DC/DC) for:.

can be used with 12V-35V for motors / heated bed.

ATmega16U2 (with enhanced firmware) for high speed USB serial connection (up to 2MBit).

Arduino 2560-R3 compatible (works with Sprinter, Repetier-Firmware, Marlin out of the box).

When you attach RUMBA for the first time to a Windows computer you might need to provide a driver (INF file).

#Arduino stepper motor serial control cable windows 8#

NEW : Easy driver setup for Windows 8/7/Vista/XP 32 and 64 bitĬLASSIC: (can cause problems with Windows 8 and Vista/7 64bit, use the easy method from above instead)

Just in case these fail, test your workshop smoke detector. Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. There is little support from Makerbase so there needs to be a page adressing setup and use of the RUMBA+. The most notable being a port for use with touchscreens (TFT) controllers. There is also a new variant offered by Makerbase the RUMBA+. RUMBA is designed to be flexible in the user's power source availability, allowing any power supply from 12V-35V. The board features a developer friendly expansion port supporting giving access to all unused I/O, ADC and I2C pins. Its six motor outputs are powered by Pololu pin compatible stepper drivers.

RUMBA is a feature rich all-in-one electronics solution for Reprap and other CNC devices. RUMBA (R.eprap U.niversal M.ega B.oard with A.llegro driver)

13.2 16U2 LUFA/Arduino based USB2Serial Firmware.

11.1 ATX power supply (controlled with RUMBA).